Energy Performance Certificate Decree, articles 1 to 4 quater: scope, definitions and the competent technician
Royal Decree 390/2021 on the energy performance certification of buildings, articles 1 to 4 quater: the purpose of the decree; definitions of the rating, the project, completed-works and existing-building certificates, the label and useful floor area; the buildings that must be certified and those excluded, including buildings bought for demolition or refurbishment. They also cover the recognised documents, the qualifications and training required of a competent technician, accreditation by responsible declaration, and the regional registration and control of technicians.
Chapter I. General provisions
Article 1. Purpose and aim.
1. The purpose of this royal decree is to lay down the technical and administrative conditions that must govern the energy performance certification of buildings and the correct transmission of the results obtained in this energy certification process to the users and owners of those buildings.
It likewise lays down the technical and administrative conditions for the approval of the methodology for calculating their energy performance rating, taking into account the factors that have the greatest effect on the energy consumption of buildings, and for the approval of the energy performance label as a common distinctive mark throughout the national territory.
2. The aim of approving that Basic Procedure is to promote energy efficiency in buildings, and to ensure that the energy they use is covered mainly by energy from renewable sources, with the consequent reduction of CO2 emissions in the building sector.
Article 2. Definitions.
For the purposes of the Basic Procedure regulated in this royal decree, the following definitions are established:
a) Energy performance rating of a building or part of a building: the expression of the energy performance of a building or part of it, determined in accordance with the calculation methodology established in the recognised document corresponding to the Basic Procedure and expressed through energy indicators by means of the energy performance label.
b) Project energy performance certification: the process by which the energy performance rating of newly constructed buildings or, where applicable, of refurbishments and extensions carried out on existing buildings is assessed on the basis of the characteristics specified in the project, and which leads to the issue of the project energy performance certificate.
c) Completed-works energy performance certification: the process by which the energy performance rating of newly constructed buildings or, where applicable, of refurbishments and extensions carried out on existing buildings is assessed on the basis of the actual characteristics of the completed building or works, allowing comparison with the rating obtained in the project energy performance certification, and which leads to the issue of the completed-works energy performance certificate.
d) Energy performance certification of an existing building or part of it: the process by which the energy performance rating obtained with the calculated or measured data of the existing building or part of it is assessed, and which leads to the issue of the energy performance certificate of the existing building.
e) Project energy performance certificate: documentation signed by the competent technician as the result of the certification process, containing information on the energy characteristics and the energy performance rating of the execution project, and recommendations for possible technically feasible interventions, individualised for each building or part of it, to improve the optimal or cost-effective levels of energy performance.
f) Completed-works energy performance certificate: documentation signed by the competent technician as the result of the certification process, containing information on the energy characteristics, the energy performance rating and recommendations for possible interventions, technically feasible and individualised for each building or part of it, to improve the optimal or cost-effective levels of energy performance of a newly constructed building or, where applicable, of a refurbishment or extension carried out on an existing building, and which allows the rating obtained in the project energy performance certification to be compared with the rating obtained once the works are finished.
g) Energy performance certificate of an existing building: documentation signed by the competent technician containing information on the energy characteristics, the energy performance rating and recommendations for possible interventions, technically feasible and individualised for each building or part of it, to improve the optimal or cost-effective levels of energy performance of an existing building or part of it.
h) Building: a roofed construction with walls in which energy is used to condition the indoor environment.
i) Energy performance of a building: the calculated or measured energy consumption estimated to be needed to meet the energy demand of the building under standardised conditions of operation and occupancy, which shall include, among other things, the energy consumed for heating, cooling, ventilation, domestic hot water production and lighting.
j) Building element: for the purposes of this royal decree, a technical building system or an element of the building envelope.
k) Primary energy: energy from renewable and non-renewable sources that has not undergone any conversion or transformation process.
l) Energy from renewable sources: energy from renewable non-fossil sources, namely wind energy, solar energy (solar thermal and solar photovoltaic) and geothermal energy, ambient energy, tidal energy, wave energy and other ocean energy, hydropower, and energy from biomass, landfill gas, sewage treatment plant gas and biogas.
m) Ambient energy: naturally occurring thermal energy and energy accumulated in a confined environment, which may be stored in the ambient air (excluding exhaust air) or in surface water or wastewater.
n) Habitable space: a space formed by one or more contiguous habitable rooms with the same use and equivalent thermal conditions, grouped together for energy calculation purposes.
ñ) Energy performance label: a public distinctive mark that certifies the existence of an energy performance certificate for the building, which has been registered, and that shows the energy performance rating level obtained by the building or part of it.
o) Thermal envelope of the building: the set of elements made up of the external enclosures and, where applicable, internal partitions of the building or part of it, including its thermal bridges, determined in accordance with the criteria laid down in the Technical Building Code (Código Técnico de la Edificación).
p) Technical building system: technical equipment for space heating and space cooling, ventilation, domestic hot water production or built-in lighting of a building, building automation and control, on-site electricity generation, or a combination of these, including systems using energy from renewable sources, of a building or a part of it.
q) Thermal installation of the building: a thermal installation is the fixed climate-control installation (heating, cooling and ventilation) intended to meet people’s demand for thermal comfort and hygiene, and/or the installation intended for the production of domestic hot water (DHW), including interconnections to district heating and/or cooling networks and automation and control systems.
r) Part of a building: a unit, floor, dwelling or apartment in a building, or premises intended for independent use or in separate legal ownership, designed or altered to be used independently.
s) Habitable room: an indoor room intended for use by people whose occupancy density and length of stay require adequate acoustic, thermal and health conditions.
t) Useful floor area: the floor area bounded by the perimeter defined by the inner face of the external enclosures of a building or of parts of a building, including half the floor area of its covered outdoor spaces for private use, measured on the horizontal projection of their roof.
The floor area occupied on plan by fixed internal enclosures, by vertical structural elements and by ducts or conduits with a horizontal cross-section of more than 100 square centimetres, and the floor area with a clear height of less than 1.5 metres, shall not be considered useful floor area.
Nor shall the area occupied by uncovered outdoor spaces be considered useful floor area.
u) Building automation and control system: a system comprising all products, software and engineering services that can support the energy-efficient, economical and safe operation of the technical building systems through automated controls and by facilitating the manual management of those technical building systems.
Article 3. Scope of application.
1. This Basic Procedure for the energy performance certification of buildings shall apply to:
a) Newly constructed buildings.
b) Existing buildings or parts of buildings that are sold or let to a new tenant.
c) Buildings or parts of buildings owned or occupied by a Public Administration, meaning by the latter the one defined in article 2.3 of Law 39/2015 of 1 October on the Common Administrative Procedure of Public Administrations, with a total useful floor area of more than 250 m².
d) Buildings or parts of buildings in which refurbishments or extensions are carried out that meet any of the following cases:
1st Replacement, installation or renewal of the thermal installations such that a thermal installations project must be drawn up or modified, in accordance with article 15 of the Regulation on Thermal Installations in Buildings, approved by Royal Decree 1027/2007 of 20 July.
2nd Intervention in more than 25 per cent of the total area of the final thermal envelope of the building.
3rd An extension that increases the built floor area or volume of the unit or units of use concerned by more than 10 per cent, where the total useful floor area added exceeds 50 m².
e) Buildings or parts of buildings with a total useful floor area of more than 500 m² intended for the following uses:
1st Administrative.
2nd Health care.
3rd Commercial: shops, supermarkets, department stores, shopping centres and similar.
4th Public residential: hotels, hostels, residences, guesthouses, tourist apartments and similar.
5th Educational.
6th Cultural: theatres, cinemas, museums, auditoriums, conference centres, exhibition halls, libraries and similar.
7th Recreational activities: casinos, amusement arcades, dance halls, discotheques and similar.
8th Catering: bars, restaurants, cafeterias and similar.
9th Passenger transport: stations, airports and similar.
10th Sports: gyms, sports centres and similar.
11th Places of worship, religious uses and similar.
f) Buildings that are required to undergo the Technical Building Inspection (Inspección Técnica del Edificio) or an equivalent inspection.
2. The following are excluded from the scope of application:
a) Buildings officially protected as part of a designated environment or because of their particular architectural or historical value, provided that any action to improve energy performance would unacceptably alter their character or appearance; the authority granting the official protection shall determine the elements that may not be altered.
b) Temporary constructions with a planned period of use of two years or less.
c) Industrial, defence and non-residential agricultural buildings, or parts of them, with low energy demand. Areas that do not need to guarantee thermal comfort conditions, such as those intended for workshops and industrial processes, shall be considered to have low energy demand.
d) Stand-alone buildings, that is, buildings not in contact with other buildings, with a total useful floor area of less than 50 m².
e) Buildings bought for demolition or for carrying out the refurbishments defined in letter d) of article 3.1. These buildings shall be exempt from obtaining the energy performance certificate of an existing building under article 10, without prejudice, where applicable, to compliance with article 9 once the refurbishment is to be undertaken, as referred to in letter d) of article 3.1.
To give effect to the exclusion in this letter e), the owner of the building or of the part of the building, as appropriate, shall make a responsible declaration (declaración responsable) to the body of the Autonomous Community or of the city of Ceuta or Melilla competent in matters of energy certification of buildings. However, the competent body of the Autonomous Community or of the city of Ceuta or Melilla may regulate a more demanding procedure.
Chapter II. Technical and administrative conditions for the energy performance certification of buildings
Article 4. Recognised documents for energy performance certification.
1. Recognised documents for energy performance certification are technical documents prepared to facilitate compliance with the Basic Procedure for the energy performance certification of buildings that have the joint recognition of the Ministry for the Ecological Transition and the Demographic Challenge and the Ministry of Transport, Mobility and Urban Agenda.
2. Recognised documents for energy performance certification may consist of the following:
a) Calculation procedures for the energy performance rating. These procedures may be simplified or general and, in order to optimise the quality of certificates, their use shall be limited according to their scope of application in the corresponding recognised documents.
b) Technical specifications and guides, or commentaries on the technical and administrative application of energy performance certification.
c) Templates for the energy performance label of the building, for the building energy assessment report (in XML format) and for certificates in physical or digital format, specifying the information to be provided in each case.
d) Any other document that facilitates the application of energy performance certification, excluding those that refer to the use of a particular or patented product or system.
3. The General Register of recognised documents for energy performance certification is attached to the Ministry for the Ecological Transition and the Demographic Challenge, through the Secretariat of State for Energy.
Article 4 bis. Requirements for practising as a competent technician for the energy performance certification of buildings.
1. A competent technician for carrying out the project energy performance certification of the buildings covered by articles 3.1.a) and 3.1.d) is a technician who holds any of the academic and professional qualifications that entitle the holder to draw up any building project or to act as works director or works execution director for building works, in accordance with Law 38/1999 of 5 November on Building Regulation (Ley de Ordenación de la Edificación). Technicians who hold a university degree carrying the entitlement to practise the regulated professions described in this same paragraph, under Royal Decree 822/2021 of 28 September establishing the organisation of university education and the procedure for assuring its quality, are likewise considered competent.
2. A competent technician for carrying out the completed-works energy performance certification of the buildings covered by articles 3.1.a) and 3.1.d), and the energy certification of the buildings covered by articles 3.1.b), 3.1.c), 3.1.e) and 3.1.f), is a technician who meets any of the following conditions:
a) Being a competent technician for carrying out the project energy performance certification of the buildings covered by articles 3.1.a) and 3.1.d) in accordance with paragraph 1 of this article.
b) Holding a university degree, other than the university degrees that qualify the holder as competent technician in the cases provided for in letter a) above, assigned to one of the following fields of knowledge listed in annex I to Royal Decree 822/2021 of 28 September establishing the organisation of university education and the procedure for assuring its quality:
1st Architecture, construction, building and urban planning, and civil engineering.
2nd Industrial engineering, mechanical engineering, automation engineering, industrial organisation engineering and navigation engineering.
3rd Electrical engineering, electronic engineering and telecommunications engineering.
4th Chemical engineering, materials engineering and natural environment engineering.
In addition, in the case of letter b), the technician must have taken and passed, with a positive assessment, module 2 of the course on basic, specific and administrative knowledge of the energy performance certification of buildings that meets the requirements of annex I to this royal decree, delivered by an entity recognised by the competent body of the Autonomous Community or of the city of Ceuta or Melilla. Passing this module shall be valid throughout the national territory, without the need for additional formalities or requirements.
Where the curriculum or teaching guides of any of the university degrees taken cover the content indicated in section 2 of annex II to this royal decree, with the minimum workloads in ECTS credits, or the minimum durations in hours, established in that annex, the course need not be taken, provided that this is evidenced by an official certificate issued by the university at which the corresponding content was taken; for this purpose the model certificate for university degrees included in section 2.1 of annex III to this royal decree, or any other official certificate containing the minimum content established in section 1 of that annex, may be used.
c) Holding a university degree assigned to one of the following fields of knowledge listed in annex I to Royal Decree 822/2021 of 28 September:
1st Environmental sciences and ecology.
2nd Earth sciences.
3rd Physics and astronomy.
4th Computer and systems engineering.
5th Mathematics and statistics.
6th Chemistry.
d) Evidencing competence standards in energy efficiency in buildings, obtained through a Higher Vocational Training qualification (Formación Profesional de Grado Superior), a Professional Certificate or a Specialisation Course, at level 3, as defined in the National Catalogue of Competence Standards. In any event, the energy certification of buildings must appear specifically in the definition of the general competence of the Vocational Training qualification, Professional Certificate or Specialisation Course.
In either of the situations in letters c) and d), the technician must have taken and passed, with a positive assessment, modules 1 and 2 of the course on basic, specific and administrative knowledge of the energy performance certification of buildings that meets the requirements of annex I to this royal decree, delivered by an entity recognised by the competent body of the Autonomous Community or of the city of Ceuta or Melilla. Passing the modules of this course shall be valid throughout the national territory, without the need for additional formalities or requirements.
Where the curriculum, teaching guides, professional modules, training modules or competence standards of any of the academic qualifications taken, or professional certificates obtained, cover the content indicated in sections 1 and 2 of annex II to this royal decree, with the minimum workloads in ECTS credits, or the minimum durations in hours, established in that annex, the course need not be taken, provided that this is evidenced by an official certificate issued by one of the following bodies:
1st The university at which the corresponding content is taken, in the case of university degrees.
2nd The entity that delivers the Vocational Training.
3rd The entity that delivers the training leading to a professional certificate, in accordance with article 80 of Royal Decree 659/2023 of 18 July implementing the organisation of the Vocational Training System.
4th The administration competent for the accreditation of professional competence for obtaining a professional certificate, in accordance with Royal Decree 659/2023 of 18 July implementing the organisation of the Vocational Training System.
For this purpose, any of the models in section 2 of annex III to this royal decree, or any other official certificate containing the minimum content established in section 1 of that annex, may be used.
Where the certificate relates to only one of the two sections of annex II to this royal decree, it shall not be necessary to take and pass the course module to which that official certificate relates.
3. In the case of discontinued qualifications that are not required to be assigned to the fields of knowledge listed in Royal Decree 822/2021 of 28 September, university qualifications assigned to the branch of knowledge of “Engineering and Architecture”, under the scheme established by Royal Decree 1393/2007 of 29 October establishing the organisation of official university education, shall be considered university qualifications covered by article 4 bis.2.c) of this royal decree.
4. In the case of qualifications obtained abroad, the holder must have the corresponding credential of homologation or, where applicable, the corresponding certificate of equivalence before submitting the responsible declaration referred to in article 4 ter.1. This requirement shall not apply to professionals who have obtained recognition of their professional qualification, in the field of regulated professions, under the provisions of European Union law.
Article 4 ter. Accreditation as a competent technician for the energy performance certification of buildings.
1. To become accredited as a competent technician for energy performance certification, of projects and completed works as well as of existing buildings, the person wishing to carry out the activity must, before starting it, submit a responsible declaration to the body competent in matters of energy certification of buildings of the Autonomous Community or of the city of Ceuta or Melilla in which he or she has his or her tax domicile. This responsible declaration must include at least the data indicated in section 1 of annex IV to this royal decree. The model in section 2 of annex IV to this royal decree may be used for the responsible declaration. The declarant may attach to the responsible declaration the documentation evidencing the requirements laid down by this royal decree, in particular those established in paragraphs 1 and 2 of article 4 bis.
2. The responsible declaration may be submitted electronically in accordance with Law 17/2009 of 23 November on free access to service activities and their exercise. It shall entitle the declarant to carry out the activity throughout the national territory, without the need for additional formalities or requirements. It shall remain effective until the competent bodies of the Autonomous Communities or of the cities of Ceuta and Melilla remove the declarant as a competent technician, either at his or her request or as a result of a finding that the conditions required for accreditation are not met.
3. In accordance with article 69.4 of Law 39/2015 of 1 October on the Common Administrative Procedure of Public Administrations, any inaccuracy, falsehood or omission of an essential nature in any data or information included in the responsible declaration, or failure to submit to the competent Administration the responsible declaration or the documentation that may be required to evidence compliance with what was declared, shall make it impossible to act as a competent technician in the certification activity from the moment such facts become known.
Article 4 quater. Register and control of competent technicians for the energy performance certification of buildings.
1. The body competent in matters of energy certification of buildings of the Autonomous Community or of the city of Ceuta or Melilla shall register the accredited competent technicians whose tax domicile is within its territorial area of competence, recording the data indicated in section 1 of annex IV to this royal decree. For this purpose, it may use the Centralised Administrative Register of Competent Technicians in the field of energy performance certification of buildings referred to in article 7 bis. If the competent body decides not to use that register, it must notify monthly to the Directorate-General for Energy Planning and Coordination of the Ministry for the Ecological Transition and the Demographic Challenge the content of the updated regional register of competent technicians, specifying the registrations and removals made. The data notified shall be incorporated into the Centralised Administrative Register of Competent Technicians by the General State Administration.
2. The body competent in matters of energy certification of buildings of the Autonomous Community or of the city of Ceuta or Melilla shall check, at least once a year, compliance with the requirements established in article 4 bis by an adequate number of competent technicians accredited and registered within its territorial area of competence.
3. Where the competent body of the Autonomous Community or of the city of Ceuta or Melilla becomes aware of an initial or supervening failure to meet the requirements laid down in article 4 bis, or of the facts referred to in article 4 ter.3, it shall require the technician to remedy any defects or errors he or she may have incurred, or to submit such submissions, documents or information as he or she considers appropriate, within fifteen days and, after processing the corresponding administrative procedure, shall issue the appropriate reasoned decision and notify it to the person concerned.
A declaration of non-compliance with the requirements laid down in article 4 bis shall make it impossible to carry out the activity. The decision may establish the obligation of the person concerned to restore the legal situation to the moment before the start of the corresponding activity, and may rule on the validity of the certificates issued during the period in which the non-compliance with the requirements is considered established, after those certificates have been subjected to the control provided for in article 11, and without prejudice to any criminal, civil or administrative liability of the non-compliant party, in line with article 69.4 of Law 39/2015 of 1 October on the Common Administrative Procedure of Public Administrations, provided that the conditions set out in that provision are met. The competent body of the Autonomous Community or of the city of Ceuta or Melilla must also notify this to those affected, where applicable, by the invalidity of the certificates issued.
The decision shall be notified to the person concerned within the period established in the regional rules governing the procedure or, failing that, within three months, after which the proceedings shall lapse in accordance with article 25.1.a) of the Law on the Common Administrative Procedure of Public Administrations. The appeals that are appropriate in each case may be brought against the decision.
Decisions declaring a responsible declaration ineffective shall be entered in the corresponding register and shall entail the entry, of the authority’s own motion, of the removal of the person concerned as a competent technician.
Where a removal from the register is made from an Autonomous Community other than the one in which the registration was made, the Autonomous Communities or the cities of Ceuta or Melilla concerned shall coordinate with each other to give effect to the removal.
4. On the basis of the information in the registers, updated periodically, the Directorate-General for Energy Planning and Coordination of the Ministry for the Ecological Transition and the Demographic Challenge shall make available to the public the first name, surnames, province and contact details of competent technicians. Personal data must be processed in accordance with Regulation (EU) 2016/679 of the European Parliament and of the Council of 27 April 2016 on the protection of natural persons with regard to the processing of personal data and on the free movement of such data, and repealing Directive 95/46/EC, and with Organic Law 3/2018 of 5 December on the Protection of Personal Data and the Guarantee of Digital Rights.
5. All activities arising from the creation, application and development of the Centralised Administrative Register of Competent Technicians that affect the staff of the competent body of the Autonomous Community or of the city of Ceuta or Melilla shall comply with the applicable basic rules on staff expenditure.
Where this sits
Next: Rating, contents, validity and control. All translated laws: Spanish laws in English.
Related on voixa.es: Spain’s 100% property tax for non-EU buyers: what happened; Modelo 210: the non-resident deadlines changed in 2026.
Nothing here is advice on your own position, and this reading is not the official text. Spain publishes no official English version of this decree; where the wording matters to a decision, read it against the Spanish original published in the BOE.